Ibase SI-06 User Manual Page 1

SI-06 Series User Manual

10 System Specifications ‧This specification is subject to change without prior notice.

11 Mechanical Specification

12 SI-06 Mounting Bracket Solution SI-06 mounting bracket (IBASE) part number: SC2SIMK1---0A1100P Install SI-06 to the mounting bracket using 4

13 SI-06 VESA Mounting Solution You can install SI-06 on plastic (LCD monitor), wood, drywall surface over studs, or a solid concrete or metal

14 Exploded View of the SI-06 Assembly Parts Description Part No. Description Part No. Description 1 Top cover 2 Main chassis 3 Rear panel 4 SI

15 Installing the memory The IB901 board supports two DDR3 memory socket for a maximum total memory of 16GB in DDR3 SO-DIMM memory type. Install

16 Setting the Jumpers The following lists the connectors on IB901 and their respective functions. Jumper Locations on IB901

17 J3: Clear CMOS Contents J3 Setting Function Pin 1-2 Short/Closed Normal Pin 2-3 Short/Closed Clear CMOS Connector Locations on IB901 Top S

18 SW1: Power Switch CN1: 3G SIM Card Slot CN2: SATA 2.5” HDD/SSD Connector CN4: Gigabit LAN Connector (Realtek RTL8111E) This RJ45 LAN conne

19 CN8: DVI-I Connector CRT via DVI-I connector Signal Name Pin # Pin # Signal Name DATA 2- 1 16 HOT POWER DATA 2+ 2 17 DATA 0- Shield 2/4 3

Revision Release Date V0.1 2013/04/11 V0.2 2014/09/23

20 BIOS Setup BIOS Introduction The BIOS (Basic Input/Output System) installed in your computer system’s ROM supports Intel processors

21 Advanced Settings This section allows you to configure and improve your system and allows you to set up some system features according to you

22 PCI Subsystem Settings Aptio Setup Utility Main Advanced Chipset Boot Security Save & Exit PCI Bus Dri

23 ACPI Settings Aptio Setup Utility Main Advanced Chipset Boot Security Save & Exit ACPI Settings Enable AC

24 CPU Configuration This section shows the CPU configuration parameters. Aptio Setup Utility Main Advanced Chipset Boot

25 iSmart Controller Aptio Setup Utility Main Advanced Chipset Boot Security Save & Exit iSm

26 USB Configuration Aptio Setup Utility Main Advanced Chipset Boot Security Save & Exit USB Co

27 Super IO Configuration Aptio Setup Utility Main Advanced Chipset Boot Security Save & Exit Super IO Co

28 Chipset Settings This section allows you to configure and improve your system and allows you to set up some system features according to your

29 Host Bridge This section allows you to configure the Host Bridge Chipset. Aptio Setup Utility Main Advanced C

3 Copyright © 2013 IBASE Technology INC. All Rights Reserved. No part of this manual, including the products and software described in it, may

30 South Bridge This section allows you to configure the South Bridge Chipset. Aptio Setup Utility Main Advanced Chipset

31 PCI Express Root Port0 Aptio Setup Utility Main Advanced Chipset Boot Security Save & Exit

32 Boot Settings Aptio Setup Utility Main Advanced Chipset Boot Security Save & Exit Boot Configuration

33 Security Settings This section allows you to configure and improve your system and allows you to set up some system features according to you

34 Save & Exit Settings Aptio Setup Utility Main Advanced Chipset Boot Security Save & Exit Save Changes

35 Drivers Installation IMPORTANT NOTE: After installing your Windows operating system, you must install first the Intel Chipset Software Insta

36 VGA Drivers Installation To install the VGA drivers, follow the steps below to proceed with the installation. 1. Click Intel(R) Cedarview Gr

37 Realtek HD Audio Driver Installation 1. Click Realtek High Definition Audio Driver. 2. On the Welcome to the InstallShield Wizard screen,

38 Realtek LAN Controller Drivers Installation Follow the steps below to install the Realtek LAN Drivers. 1. Click Realtek GbE_FE Ethernet P

39 Appendix A. I/O Port Address Map Each peripheral device in the system is assigned a set of I/O port addresses which also becomes the identi

4 Table of Contents Setting up your system ...

40 Address Device Description 03F8-03FF Communications Port (COM1) 04D0-04D1 Programmable interrupt controller 0D00-FFFF PCI bus E000-E0FF Rea

41 B. Interrupt Request Lines (IRQ) Peripheral devices use interrupt request lines to notify CPU for the service required. The following table

42 C. Watchdog Timer Configuration The WDT is used to generate a variety of output signals after a user programmable count. The WDT is suitabl

43 printf("System will reset after %d seconds\n", bTime); if (bTime) {EnableWDT(bTime);}else {DisableWDT(); } return 0; } //---------

44 void DisableWDT(void) { unsigned char bBuf; Set_F81801_LD(0x07); //switch to logic device 7 bBuf = Get_F81801_Reg(0xFA); bBuf &

5 Safety Information Your SI-06 is designed and tested to meet the latest standards of safety for information technology equipment. However, to

6 Care during use  Do not walk on the power cord or allow anything to rest on it.  Do not spill water or any other liquids on your system.

7 Acknowledgments  AMI is a registered trademark of AMI Software International, Inc.  Intel are registered trademarks of Intel Corporation.

8 Accessories Components I/O View Refer to the diagram below to identify the components on this side of the system.

9 Power Button The power switch allows powering ON and OFF the system. HDD The hard disk LED blinks when data is being written into or read fro