Ibase IOPS-76 User Manual

iOPS-76 Series User Manual 2012 Jul V1

10 Intel® Open Pluggable Specification The Intel® Open Pluggable Specification (OPS) is an effort to standardize the connector and signals betwee

11 iOPS-76 + iOPS-EK1 iOPS-76 + iOPS-EK2

12 Exploded view of the iOPS-76 assembly Parts description Part NO. Description Part NO. Description 1 Front panel 2 Bottom cover 3 Main chassis

13 following steps: 1. Hold the DDR3 module so that the key of the DDR3 module aligns with that on the memory slot. Insert the module into the so

14 Signal definitions Power & Ground Signals DVI-D Signals

15 Display Port Signals Audio Signals USB Signals UART Signals

16 Control Signals

17 Reserved Pins Drivers Installation This section describes the installation procedures for software and drivers. The software and drivers a

18 Intel Chipset Software Installation Utility The Intel Chipset Drivers should be installed first before the software drivers to enable Plug &

19 2. When the Welcome screen to the Intel® Chipset Device Software appears, click Next to continue. 3. Click Yes to accept the softwa

2 Copyright © 2012 IBASE Technology INC. All Rights Reserved. No part of this manual, including the products and software described in it, may be

20 4. Click Next to continue the installation process.

21 5. On the Readme File Information screen, click Next to continue the installation. 6. The Setup process is now complete. Click Finish to re

22 VGA Drivers Installation NOTE: Before installing the Intel(R) Q77 Chipset Family Graphics Driver, the Microsoft .NET Framework 3.5 SPI shoul

23 2. Click Intel(R) Q77 Chipset Family Graphics Driver. DRIVERS INSTALLATION 54 3. When the Welcome screen appears, click Next to continue.

24 4. Click Yes to to agree with the license agreement and continue the installation. DRIVERS INSTALLATION 5. On the Readme File Information sc

25 6. On Setup Progress screen, click Next to continue. 7. Setup complete. Click Finish to restart the computer and for changes to take effect.

26 Realtek HD Audio Driver Installation Follow the steps below to install the Realtek HD Audio Drivers. 1. Insert the CD that comes with the

27 3. On the Welcome to the InstallShield Wizard screen, click Next to proceed with and complete the installation process. 4. The InstallShield

28 LAN Drivers Installation 1. Insert the CD that comes with the board. Click Intel and then Intel(R) Q7 Series Chipset Drivers. 2. Click Int

29 3. Click Install Drivers and Software. 4. Click Next to to agree with the license agreement.

3 Table of Contents Safety Information ... 4 Setting

30 5. Click the checkbox for Drivers in the Setup Options screen to select it and click Next to continue. DRIVERS INSTALLATION 6. The wizard is

31 7. When InstallShield Wizard is complete, click Finish. DRIVERS INSTALLATION 8. When InstallShield Wizard is complete, click Finish.

32 Intel® Management Engine Interface Follow the steps below to install the Intel Management Engine. 1. Insert the CD that comes with the boar

33 3. Click Yes to to agree with the license agreement. DRIVERS INSTALLATION

34 4. When the Setup Progress screen appears, click Next. Then, click Finish when the setup progress has been successfully installed. DRIVERS INS

35 Intel® USB 3.0 Drivers 1. Insert the CD that comes with the board. Click Intel and then Intel(R) Q7 Series Chipset Drivers. 2. Click Intel

36 4. Click Yes to to agree with the license agreement and continue the installation. 5. On the Readme File Information screen, click Next to

4 Safety Information Your SI-38 is designed and tested to meet the latest standards of safety for information technology equipment. However, to e

5 Always unplug all power, and network cables from the power outlets before cleaning the system.  If you encounter the following technical probl

6 Acknowledgments  AMI is a registered trademark of AMI Software International, Inc.  Intel are registered trademarks of Intel Corporation. 

7 Accessories Components I/O View Refer to the diagram below to identify the components on this side of the system. Power Bottom The power sw

8 to a local network. USB1/2 The USB (Universal Serial Bus 3.0) port is compatible with USB devices such as keyboards, mouse devices, cameras, an

9 Mechanical Specification Assembly iOPS-76 series to the OPS display You can assembly iOPS-76 series into all OPS (Open Pluggable Specificatio