Ibase SI-38N User Manual

SI-38N Series User Manual 2013 Sep. V1

10 You can install SI-38N on plastic (LCD monitor), wood, drywall surface over studs, or a solid concrete or metal plane directly. Ensure the ins

11 Mounting to hollow walls  Method 1: Wood surface – A minimum wood thickness – 38mm (1.5in.) by 25.4 cm (10in.) – of high, construction – grad

12 Parts description Part NO. Description Part NO. Description 1 IB939 MB 2 Base 3 Heat sink 4 Main chassis 5 I/O bracket 6 Wall mount kit 7 HDD

13 Installing the memory The IB939 board supports two DDR3 memory socket for a maximum total memory of 8GB in DDR3 SO-DIMM memory type. Installi

14 J15: Clear CMOS Setting Page 14 Jumper Locations on IB939 JP4, JP5: COM4 RS232 RI/+5V/+12V Power Setting JP4/JP5 Setting Function Pin 1-2

15 Normal Clear CMOS Connectors on IB939 Connector Locations on IB939 CN19: DC_IN Connector (+12V Adaptor 4 Pin) Pin # Signal Name 1

16 SW1: Power Button LED3: Power LED (Green), HDD LED (RED) The green LED at the bottom is power LED. The red LED on top is the HDD LED. COM1

17 CN3: DVI-I Connector CN18: Audio MIC-in CN17: Audio Line out JP13: SPI Flash Connector J8: Half Mini PCIE Slot JP9: LPC Debug Port Connect

18 OUT2 5 6 OUT0 IN3 7 8 IN1 IN2 9 10 IN0 JP10: US2.0 Connector Signal Name Pin # Pin # Signal Name Vcc 1 2 Ground D- 3 4 D+ D+ 5 6 D- Ground 7

19 2 NC 3 Ground J24: CPU_FAN Connector This is a 3-pin header for the CPU fan. The fan must be a 12V (500mA). Pin # Signal Name 1 Ground 2 +12V

2 Copyright © 2012 IBASE Technology INC. All Rights Reserved. No part of this manual, including the products and software described in it, may be

20 BIOS Setup BIOS Introduction The BIOS (Basic Input/Output System) installed in your computer system’s ROM provides critical low-lev

21 Main BIOS Setup This setup allows you to record some basic hardware configurations in your computer system and set the system clock. Aptio Se

22 System Language Choose the system default language. System Date Set the Date. Use Tab to switch between Data elements. System Time Set the Ti

23 PCI Latency Timer Value to be programmed into PCI Latency Timer Register. VGA Palette Snoop Enables or disables VGA Palette Registers Snooping.

24 CPU Configuration This section shows the CPU configuration parameters. Aptio Setup Utility Main Advanced Chipset Boot S

25 Enable/disable CPU Virtualization. CPB Mode Enable/disable CPB. C6 Mode Auto/disable CPB. Node 0 Information View memory information related

26 EuP/ErP control on S5 options: [Keep standby power] Enable All of the standby power and ignore EuP/ErP specification. [Ethernet Only] Only prov

27 ACPI Shutdown Temperature The default setting is Disabled. Auto Power On Schedule Aptio Setup Utility Main Advanced Chipset

28 EHCI Hand-off Enabled +- Change Field F1: General Help F2: Previous Values F3: Optimized Default F4: Save ESC: Exit USB hardware d

29 NCT6106D Super IO Configuration Aptio Setup Utility Main Advanced Chipset Boot Security Save & Exit NCT6106D Super IO

3 Table of Contents Safety Information ... 4 Setting

30 ESC: Exit Temperatures/Voltages These fields are the parameters of the hardware monitoring function feature of the motherboard

31 AMD Reference code Version: Trinity PI 1.0.0.3 Options for SATA Configuration → ← Select Scre

32 OnChip SATA Type Native IDE /n RAID /n AHCI /n AHCI /n Legacy IDE /n IDE->AHCI /n HyperFlash OnChip IDE mode Legacy mode or Native mode SA

33 XHCI0 Port 0 Enabled F4: Save ESC: Exit XHCI0 Port 1 Enabled XHCI1 Port 0 Enabled XHCI1 Port 1 Enabled Aptio Setup Utility Main

34 Enter: Select +- Change Field F1: General Help F2: Previous Values F3: Optimized Default F4: Save ESC: Exit Integrated

35 Setup Prompt Timeout 1 → ← Select Screen ↑↓ Select Item Enter: Select +- Change Field F1: General Help F2: Previous Values F3: O

36 UPON REQUEST – GA20 can be disabled using BIOS services. ALWAYS – do not allow disabling GA20; this option is useful when any RT code is execut

37 This option controls what devices system can boot to. Launch PXE OpROM policy Controls the execution of UEFI and Legacy PXE OpROM. Launch Sto

38 User Password F2: Previous Values F3: Optimized Default F4: Save ESC: Exit UEFI Secure Boot Management Secure Boot control Enabled ► S

39 Save Changes → ← Select Screen ↑↓ Select Item Enter: Select +- Change Field F1: General Help F2: Previous Values F3: Optimized Defau

4 Safety Information Your SI-38N is designed and tested to meet the latest standards of safety for information technology equipment. However, to e

40 Restore User Defaults Restore the User Defaults to all the setup options. Launch EFI Shell from filesystem device Attempts to Launch EFI Shell

41 VGA Drivers Installation 1. Insert the drivers DVD that comes with the board. Click AMD, then AMD A70M Chipset Drivers. 2. Click AMD A70M

42 4. Select the language you would like to be displayed and click Next. 5. Click Next to continue the installation process. 6. Se

43 7. Click Accept to accept the End User License Agreement. 8. To reboot the system, click Yes.

44 Audio Drivers Installation 1. Insert the drivers DVD that comes with the board. Click AMD, then Realtek High Definition Audio Driver. 2. Wh

45 3. Click Realtek RTL8111E LANDrivers. 4. When the Welcome screen appears, click Next. 5. Now click Install to begin the installa

46 Appendix A. I/O Port Address Map Each peripheral device in the system is assigned a set of I/O port addresses, which also becomes the ide

47 0070h-0073h System CMOS/real time clock 0074h-007Fh Motherboard resources 0080h-0090h Direct memory access controller 0091h-0093h Motherboard r

48 Level Function IRQ 0 System timer IRQ 1 Standard 101/102-Key IRQ 3 Communications Port (COM2) IRQ 4 Communications Port (COM1) IRQ 8 System C

49 IRQ 19 PCI standard PCI-to-PCI bridge IRQ 19 AMD AHCI Compatible RAID Controller C. Watchdog Timer Configuration The WDT is used to generate

5 cleaning the system.  If you encounter the following technical problems with the product, unplug the power cord and contact a qualified servic

50 unsigned char bBuf; unsigned char bTime; char **endptr; // char SIO; printf("6106 watch dog program\n"); bTime = strto

51 //switch to logic device 8 Set_6106_Reg(0x30, 0x01); //enable timer Set_6106_Reg(0xF1, interval); //set timer } //-----

52 ucDid = Get_6106_Reg(0x20); if (ucDid == 0x07) //Fintek 81865 { goto Init_Finish; } F81865_BASE = 0x2E; result = 6106_BASE;

53 outportb(6106_INDEX_PORT, 6106_UNLOCK); } //--------------------------------------------------------------------------- void Lock_6106 (void)

6 Acknowledgments  AMI is a registered trademark of AMI Software International, Inc.  AMD and ATI are registered trademarks of AMD Corporatio

7 Accessories Components I/O View Refer to the diagram below to identify the components on this side of the system. Power Bottom The power sw

8 HDD The hard disk LED blinks when data is being written into or read from the hard disk Power The power LED illuminated when system been power

9 jack. Power supplied through this jack supplies power to the system. To prevent damage to the system, always use the supplied power adapter. Sp