Ibase SI-18 User Manual

SI-18 Series User Manual

10 Specification System Mainboard EB-900 Construction SGCC 1.0t Chassis Color Black / White Storage 2.5” 80GB SATA HDD x 1 Mounting Wall mount Dimen

11 Mounting SI-18 to the Wall You can install SI-18 on plastic (LCD monitor), wood, drywall surface over studs, or a solid concrete or metal plane

12 Mounting to hollow walls  Method 1: Wood surface – A minimum wood thickness – 38mm (1.5in.) by 25.4 cm (10in.) – of high, construction – grade

13 SI-18 mounting bracket solution SI-18 mounting bracket (IBASE) part number: SC2SIMK1---0A1100P Please install SI-18 to the mounting bracket usin

14 Exploded view of the SI-18 assembly Parts description Part No. Description Part No. Description 1 HDD 2 HDD bracket 3 EB900 4 FAN Set 5 Fan br

15 Installation Installing WLAN antenna (Optional) SI-18 has reserved one SMA connector hole for WLAN (wireless LAN) antenna connection on the I/O s

16 4. Use a screw driver to pinch out the knock-out metal-plate of the SMA antenna hole from point B. To avoid any metal falling into the system, p

17 6. Install the antenna washer, then the hex nut on the SMA connector and use a hex socket driver or pliers to fix the nut and secure the SMA con

18 8. Wire the IPX connector on WLAN card and arrange the internal antenna cable routing. 9. Screw the bottom chassis back to the system with 8 s

19 Installing the memory The mainboard supports two DDR3 memory socket for a maximum total memory of 4GB in DDR3 memory type. Installing and Remo

Revision Release Date V0.1 2011/11/15 V0.2 2014/09/23

20 Setting Jumper Jumpers are used on the motherboard to select various settings and features according to your needs and applications. Contact your

21 JP2: LCD Panel Power Selection JP2 LCD Panel Power 3.3V 5V JP6: COM1 RS232 +5V/+12V Power Setting JP6 Setting Function Pin 1-2 Short/Close

22 BIOS Setup This chapter describes the different settings available in the AMI BIOS that comes with the board. BIOS Introduction The BIOS (B

23 Main BIOS Setup This setup allows you to record some basic hardware configurations in your computer system and set the system clock. Note: If th

24 Advanced Settings This section allows you to configure and improve your system and allows you to set up some system features according to your pr

25 PCI Subsystem Settings This section allows you to configure the PCI, PCI-X and PCI Express settings. PCIE Configuration The fields under PCIE C

26 System BIOS Cacheable The setting of Enabled allows caching of the system BIOS ROM at F000h-FFFFFh, resulting in better system performance. Ho

27 ACPI Settings This section configures the system ACPI parameters. Enabled ACPI Auto Configuration Enables or Disables BIOS ACPI Auto Configurati

28 CPU Configuration This section shows the CPU configuration parameters. Limit CPUID Maximum Disabled for Windows XP. PSS Support Enabled /disable

29 Auto Power On Schedule This section setups the power on time for the system. Schedule Slot 1 Setup the hou/minute for sytem power on. Schedu

3 Copyright © 2011 IBASE Technology INC. All Rights Reserved. No part of this manual, including the products and software described in it, may be r

30 USB Configuration Legacy USB Support Enables Legacy USB support. AUTO option disables legacy support if no USB devices are connected. DISABL

31 Super IO Configuration Serial Port 0/1 Configuration Set Parameters of Serial Port 0/1 (COMA/COMB) Power Failure The options: Keep last state, B

32 Chipset Settings This section allows you to configure and improve your system and allows you to set up some system features according to your pre

33 North Bridge This section allows you to configure the North Bridge Chipset. IOMMU Mode IOMMU is supported on LINUX based systems to convert 32bi

34 GFX Configuration PSPP Policy PCIe speed power policy. Memory Configuration Integrated Graphics Enable Integrate Graphics controller. Node 0

35 North Bridge LVDS Config Select South Bridge This section allows you to configure the South Bridge Chipset.

36 SB SATA Configuration OnChip SATA Type Native IDE / n RAID / n AHCI / n AHCI / n Legacy IDE / n IDE->AHCI / n HyperFlash

37 SB USB Configuration SB GPP Port Configuration

38 SB HD Azalia Configuration Boot Settings This section allows you to configure the boot settings according to your preference. Setup Prompt Tim

39 Quiet Boot Enables/Disables Quiet Boot option. GateA20 Active UPON REQUEST – GA20 can be disabled using BIOS services. ALWAYS – do not allow disa

4 Table of Contents Acknowledgments ... 7 Accessorie

40 Save & Exit Settings Save Changes and Exit Exit system setup after saving the changes. Disacard Changes and Exit Exit system setup witho

41 Restore Defaults Restore/Load Defaults values for all the setup options. Save as User Defaults Save the changes done so far as User Defaults. R

42 Driver Installation This section describes the installation procedures for software and drivers. The software and drivers are included with the m

43 AMD A55E Chipset Family Graphic Driver Installation Follow the steps below to install the AMD A55E chipset family graphics drivers. 1. Insert t

44

45 3. Select Express and click Next to proceed with the installation. On the following screen, click Finish to complete the installation process.

46

47 Realtek High Definition Audio Driver Installation Follow the steps below to install the Realtek HD audio drivers. 1. Insert the CD that comes wi

48 2. When the welcome screen to the Audio Driver Setup appears, click Next to start the software installation. Once the InstallShield Wizard is com

49 Realtek LAN Controller Drivers Installation Follow the steps below to install the Realtek LAN drivers. 1. Insert the CD that comes with the syst

5 Safety Information Your SI-18 is designed and tested to meet the latest standards of safety for information technology equipment. However, to ens

50 3. When the Welcome screen of the InstallShield Wizard appears, click Next to continue. 4. When the InstallShieldWizard has finished installin

51

6 Care during use  Do not walk on the power cord or allow anything to rest on it.  Do not spill water or any other liquids on your system. 

7 Acknowledgments  AMI is a registered trademark of AMI Software International, Inc.  AMD and ATI are registered trademarks of AMD Corporation.

8 Accessories a. Power Cord x 1 b. Driver CD x 1 c. Power Brick x 1

9 Components I/O View Refer to the diagram below to identify the components on this side of the system. DVI The Digital Visual Interface (DVI) port